Famco Flue Liner Replacement Nationwide

Famco Flue Liner Replacement: The Orlando Owner’s Guide

If you have a Famco flue liner that’s rusted through, warped, or separated at a seam, replacement in Orlando typically runs $1,450 – $2,800 installed, depending on the liner diameter, the height of your chimney chase, and whether we’re doing a straight swap or dealing with water damage behind it. We keep common Famco-compatible rigid liner sections and connectors on our trucks, so for most single-story homes in neighborhoods like College Park or Conway, we can complete the job same day once we’ve measured and confirmed the part fit.

Call (904) 822-8172

Most Orlando homeowners discover the liner has failed one of two ways: either they see rust flakes and water staining around the fireplace during a rainy stretch, or they smell a stale, smoky odor that lingers even with the damper closed. Famco makes solid products, but Florida humidity and summer downpours are unforgiving on steel liners, especially if the chase top or cap has been leaking for a season or two. The liner is the metal tube inside your chimney that carries combustion gases up and out. When it fails, those gases, moisture, and acidic residue start creeping into places they should never be.

Which Famco Models This Applies To

Famco’s rigid stainless and galvanized liners come in standard diameters sized for masonry and factory-built chimneys alike, and the part numbers usually live on a metal tag near the liner’s top section or stamped along a seam. We most often match replacements for Famco’s 5.5″, 6″, 7″, and 8″ round rigid liner systems, though we’ve pulled 10″ oval-to-round transitions on a handful of larger custom builds near Winter Park. The rule we use on every job: measure twice at three points (top, middle, and at the appliance collar), because a liner that’s been heat-cycled for ten years can measure a full quarter-inch different from its stamped spec.

On the OEM-versus-aftermarket question for Famco specifically: we’ll always quote a genuine Famco liner or a direct-compatible equivalent from a manufacturer we trust, like DuraFlex or HeatShield, when a Famco part is discontinued or backordered. The compatibility gotcha with Famco rigid liner is the locking seam profile. Some big-box generic liners technically measure 6″, but the seam roll doesn’t seat correctly into Famco’s couplers, which leaves a gap that leaks flue gas. We’ve seen that exact issue on homes in Baldwin Park where another contractor had used a mismatched section. It’s why we verify the seam profile, not just the diameter, before ordering or installing anything.

Signs Your Famco Flue Liner Replacement Is Failing

• Rust flakes or reddish-brown staining inside the firebox. This means water is entering the chase and sitting against the liner. In Orlando, we see this most after hurricane-season rains if the chase pan or chimney cap has lost its seal.
• A stale smoke smell in the house, even when the fireplace hasn’t been used in weeks. The liner has likely developed a pinhole or seam separation, and the chimney is drafting leftover combustion odor back down into the living space.
• Visible warping or buckling on the liner’s exposed sections when you shine a light up from the firebox. Steel that has overheated and cooled repeatedly will eventually deform, especially if the fireplace was fired hot with dry, fast-burning woods.
• Pieces of thin metal or flaky scale falling into the firebox. That’s delamination of the liner wall itself. The structural integrity is already gone by the time you see this, and the metal has likely been compromised for a season or more.
• Water dripping down the outside of the chimney chase or staining on the ceiling near the fireplace. The chase top, not the liner itself, usually causes this. But by the time water is running down the outside, the interior liner has typically been wet repeatedly and needs an inspection regardless.

Replacement Cost & What’s Included

We quote Famco flue liner replacement in Orlando as a fixed, written price before any work begins. For a standard single-story home, expect $1,450 – $1,900 for a 6″ rigid liner swap including new connectors and couplers. Two-story homes and taller chases push that toward $2,100 – $2,800 due to the extra liner sections, lift work, and longer install time. If the chase top, cap, or flashing also needs replacement, we break that out as a separate line item so you see exactly what you’re paying for.

What drives the range, honestly: liner diameter, liner length, whether the existing liner is so deteriorated it needs cutting out in pieces, and whether we find water damage behind it that should be addressed now rather than later. Every replacement includes the new liner sections, couplers, a proper top plate if needed, and our 365-Day Done Right Promise: a written guarantee on the repair, and if it fails within a year, we come back and make it right free. Famco repair work in Orlando shouldn’t be a gamble. You get a price, a photo report, and a guarantee, in that order.

DIY or Call Us?

You can absolutely inspect the exposed bottom section of your liner with a flashlight from inside the firebox. Look for flaking metal, visible seams pulling apart, and rust staining. You can also go outside after a rainstorm and note whether the chase top looks intact or if the cap is missing entirely. Where DIY goes wrong is the swap itself. Rigid liner sections are heavy, and getting a replacement seated correctly at the appliance collar while working from the roof requires two people, a proper rigging setup, and a good read on how the liner connects at both ends.

Beyond that, there’s a carbon monoxide layer to this. A liner that isn’t seated or sealed correctly can quietly put combustion gases into your home. That’s not a “watch a video and figure it out” situation. If you have a Famco liner that’s failing, call us at (904) 822-8172 and we’ll come out, measure it, show you photos of what’s actually happening, and give you a written price before anything gets touched.

FAQs